Diff for "TelescopeSystemStatus" - www.iram.es Main Wiki

Differences between revisions 1 and 32 (spanning 31 versions)

System - General

$/!\$ The 30-m telescope is now operating using the New Control System (NCS) (2005-11-30 HU)

Some of the information below, especially about available observing features and problems, refers to the old control system (OLD CS). It will be updated soon.

[#beginOfPage Back to top]

Antenna

[#beginOfPage Back to top]

Wobbler

$/!\$ Observing configuration sometimes is not transfered to the wobbler control system and when fails W. Brunswig has to restart his communication programs (since January 2005). Wobbler config. can be set manually by operator (OLD CS)

Wobbler rotation implemented. Current range: +/- 60deg (2004-12-01 AW) (OLD CS)

[#beginOfPage Back to top]

Pointing Model

heterodyne: OK (last model update: 2005-04-30 ). (OLD CS)

bolometer: OK (last model update: 2004-11-02 ). (OLD CS)

$/!\$ Operator/AOD: Check regularly that automatic P4 P5 is working (2002-12-13).BR Narrowband continuum pointing (for SiO masers) is out of service! (2003-07-09, 2003-07-30)

[#beginOfPage Back to top]

SIS Receivers

A, B, C and D receivers are aligned within 3", checked (2003-09-24)

$/!\$ Receiver C150 shows low continuum signal at the higher frequencies (>168 GHz) It has to be fully checked. Use D150 instead. (2005-11-16)

Calibration Tcold temperatures have been checked by receiver group. New scaling factor of 0.94 has been implemented into obs.(OLD CS) Obs Tcold should be OK (2005-06-28) (OLD CS)

[#beginOfPage Back to top]

Pointing and Flux monitoring with SIS receivers:

Continuum instability ("ripple") can occur with all receivers, making pointing and focusing difficult.

In general some receivers are better then others in this respect as summarized here:
- A100 generally OK for pointing. (2003-11-12) BR B100 OK, is best for pointing, but is out of operation (2005-11-30)! BR $/!\$ C150 often bad for pointing, ripple. (2002-07-16) BR D150 generally good performance for pointing.(2002-07-16) BR $/!\$ A230 often unstable, bad for pointing and flux monitoring. (2003-11-12) BR B230 OK BR $/!\$ C270 very bad for pointing at 265 Ghz. (2002-07-16) BR $/!\$ D270 can be unstable and difficult for pointing. (2002-07-16) BR
  HERA pointing difficulties using beam switch mode - total power mode gave better results but requires excellent weather BR Wobbler switching may avoid ripple, beamswitching is most sensitive to ripple

[#beginOfPage Back to top]

HERA

Second polarization installed. $/!\$ One blind pixel. BR SSB tuning tables for standard frequencies. BR Sideband rejections not determined (2004-12-01 AW) BR

$/!\$ Watch the computer control of the derotator closely (2002-12-22). BR $/!\$ Make sure the derotator tracking is stopped after observations, i.e, set to zero degrees in "frame". BR $/!\$ With VESPA, the maximum of 4 spectra per pixel can be used. BR $/!\$ $/!\$ Much higher noise in HERA 2 than HERA 1 when using Vespa. This is being investigated by S. Navarro [RM 30.6.2005]BR $/!\$ When using HERA 1 and 2 configure only 1 Channel for continuum observations in OBS, never-the-less the continuum drifts of all channels are reduced (calibrated) by ODP [AS 11.10.2005]

[#beginOfPage Back to top]

Bolometers

Mambo II is installed and ready for operation (AW 2004-12-01)

[#beginOfPage Back to top]

Backends

$/!\$ 1 MHz Filterbank not yet integrated in new control system (RM 7.12.05)

256 MHz shift in 100kHz FB header (AW 2004-12-01) (OLD CS) Software and/or hardware problem in the 1MHz FB - problem is currently investigated (AW 2004-12-01) (OLD CS)
Spikes in VESPA at intersection of different units (AW 2004-12-01) BR

[#beginOfPage Back to top]

Computer/Software

[#beginOfPage Back to top]

Other Items

[#beginOfPage Back to top]

Updates/History

To see the changes between the actual and the last version, please see Show Changes in the Wiki Interface. If you want to see the Revision History of this page, please see Get Info in the Wiki Interface.

[#beginOfPage Back to top]

Legend

: OKBR $/!\$ : WarningBR : ErrorBR

The wiki markup of these icons is:

{{{(./) : OK $/!\$ : Warning : Error }}}

[#beginOfPage Back to top]

-  ⇤ ← Revision 1 as of 2005-04-21 16:25:33 → 
  Size: 4572
  Editor: gra-lx8
  Comment:
+   ← Revision 32 as of 2005-12-07 09:34:14 → ⇥
  Size: 5183
  Editor: visitor11
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
+#acl RainerMauersberger:read,write WalterBrunswig:read,write SantiagoNavarro:read,write DavidJohn:read,write JuanPenalver:read,write SalvadorSanchez:read,write ManuelRuiz:read,write FernandoAnel:read,write MarianoEspinosa:read,write EnriqueLobato:read,write DavidMartinez:read,write  JuanLuisSantaren:read,write NuriaMarcelino:read,write HansUngerechts:read,write SergioMartin:read,write AlbrechtSievers:read,write AxelWeiss:read,write FredericDamour:read,write GabrielPaubert:read,write KarlSchuster:read,write RosaMontalban:admin,read,write VictorEspigares:admin,read,write All:read
##language:en
#pragma section-numbers off
-Line 3:
+Line 6:
-= Telescope System Status =
-Line 5:
+Line 7:
-''(Date 2004-12-01)''
 Line 12:
-NORMAL OPERATION
+/!\ The 30-m telescope is now operating using the New Control System (NCS) (2005-11-30 HU)

Some of the information below, especially about available observing features and problems, refers to the old control system (OLD CS).  It will be updated soon.
-Line 18:
+Line 20:
-OK
+(./) OK
-Line 24:
+Line 26:
-Avoid wobbler throw of 120"; with a throw of 120" the specification of a phase time may not work properly.  With a throw of 119 or 121 is should be OK. (2003-07-09)
Results from first pointing after unlocking the wobbler can be  wrong! Usually it's sufficient to ignore the first pointing and repeat the pointing (2003-07-09)
+/!\ Observing configuration sometimes is not transfered to the wobbler control system and when fails W. Brunswig has to restart his communication programs (since January 2005). Wobbler config. can be set manually by operator (OLD CS)
-Line 27:
+Line 28:
-Wobbler rotation implemented. Current range: +/- 60deg (2004-12-01 AW)
+Wobbler rotation implemented. Current range: +/- 60deg (2004-12-01 AW) (OLD CS)
-Line 33:
+Line 34:
-heterodyn: OK (last model update: 2004-11-17 ).
bolometer: OK (last model update: 2004-11-02 ).
+heterodyne: OK (last model update: 2005-04-30 ). (OLD CS)
 Line 36:
-Operator/AOD: Check regularly that automatic P4 P5  is working (2002-12-13).
Narrowband continuum pointing (for SiO masers) is out of service! (2003-07-09, 2003-07-30)
+bolometer: OK (last model update: 2004-11-02 ). (OLD CS)


/!\ Operator/AOD: Check regularly that automatic P4 P5  is working (2002-12-13).[[BR]]
{X} Narrowband continuum pointing (for SiO masers) is out of service! (2003-07-09, 2003-07-30)
-Line 45:
+Line 48:
+/!\ Receiver C150 shows low continuum signal at the higher frequencies (>168 GHz)
It has to be fully checked. Use D150 instead. (2005-11-16)
-Line 46:
+Line 52:
-New scaling factor of 1.0 has been implemented into obs.
Obs Tcold should be ok (2004-01-17)
+New scaling factor of 0.94 has been implemented into obs.(OLD CS)
Obs Tcold should be OK (2005-06-28) (OLD CS)
-Line 53:
+Line 61:
-Continuum instability ("ripple") can occur with all receivers, making pointing and focussing difficult.
+Continuum instability ("ripple") can occur with all receivers, making pointing and focusing difficult.
-Line 56:
+Line 64:
-    A100 generally OK for pointing. (2003-11-12)
    B100 OK, will be replaced  (2003-11-12)
    C150 often bad for pointing, ripple. (2002-07-16) 
    D150 generally good performance for pointing.(2002-07-16)
    A230 often unstable, bad for pointing and flux monitoring. (2003-11-12) 
    B230 OK, will be replaced (2003-11-12)
    C270 very bad for pointing at 265 Ghz. (2002-07-16)
    D270 can be unstable and difficult for pointing. (2002-07-16)
    HERA pointing difficulties using beam switch mode - total power mode gave better results (2004-01-17)
+    A100 generally OK for pointing. (2003-11-12) [[BR]]
    B100 OK, is best for pointing, but is out of operation (2005-11-30)! [[BR]]
    /!\ C150 often bad for pointing, ripple. (2002-07-16) [[BR]]
    D150 generally good performance for pointing.(2002-07-16) [[BR]]
    /!\ A230 often unstable, bad for pointing and flux monitoring. (2003-11-12) [[BR]]
    B230 OK [[BR]]
    /!\ C270 very bad for pointing at 265 Ghz. (2002-07-16) [[BR]]
    /!\ D270 can be unstable and difficult for pointing. (2002-07-16) [[BR]]

    HERA pointing difficulties using beam switch mode - total power mode gave better results but requires excellent weather [[BR]] 
    Wobbler switching may avoid ripple, beamswitching is most sensitive to ripple
-Line 70:
+Line 80:
-Second polarization installed. One blind pixel.
No SSB tuning tables except for few standard frequencies.
Sideband rejections not determined   (2004-12-01 AW)
+Second polarization installed. /!\ One blind pixel. [[BR]]
SSB tuning tables  for  standard frequencies. [[BR]]
Sideband rejections not determined   (2004-12-01 AW) [[BR]]
-Line 75:
+Line 85:
-Watch the computer control of the derotator closely (2002-12-22). 
Make sure the derotator tracking is stopped after observations, i.e, set to zero degrees in "frame".
With VESPA, only two spectra per pixel can be used.
+/!\ Watch the computer control of the derotator closely (2002-12-22). [[BR]]
/!\ Make sure the derotator tracking is stopped after observations, i.e, set to zero degrees in "frame". [[BR]]
/!\ With VESPA, the maximum of 4 spectra per pixel can be used. [[BR]]
/!\ /!\ Much higher noise in HERA 2 than HERA 1 when using Vespa. This is being investigated by S. Navarro [RM 30.6.2005][[BR]]
/!\ When using HERA 1 and 2 configure only 1 Channel for continuum observations in OBS, never-the-less the continuum drifts of all channels are reduced (calibrated) by ODP [AS 11.10.2005]
-Line 89:
+Line 101:
-MHz shift in 100kHz FB header (AW 2004-12-01)
 Software and/or hardware problem in the 1MHz FB  - problem is currently investigated (AW 2004-12-01)
 Spikes in VESPA at intersection of different units (AW 2004-12-01)
+/!\ 1 MHz Filterbank not yet integrated in new control system (RM 7.12.05)

 256 MHz shift in 100kHz FB header (AW 2004-12-01) (OLD CS)

 Software and/or hardware problem in the 1MHz FB  - problem is currently investigated (AW 2004-12-01) (OLD CS)

 Spikes in VESPA at intersection of different units (AW 2004-12-01) [[BR]]
-Line 97:
+Line 113:
-Mirroring between IRAM Grenoble ( http://www.iram.fr ) and Granada( http://www.iram.es/ ) websites sometimes takes several days to update.   (2003-07-01)
-Line 110:
+Line 126:
-''(in reverse order by date!)''

    2004-12-01 AW [[BR]]
    2004-07-24 RM [[BR]]
    2004-03-24, 25 HU [[BR]]
    2004-01-17 AW [[BR]]
    2003-11-12 HU [[BR]]
    2003-09-25 MR [[BR]]
    2003-09-08 HU [[BR]]
    2003-08-20 HU [[BR]]
    2003-08-05 AS [[BR]]
    2003-07-09 RM [[BR]]
    2003-07-01,04/5, 7 HU [[BR]]
    2003-06-08, 09 HU [[BR]]
    2003-04-22, 26 HU [[BR]]
    2003-04-06 AS [[BR]]
    2003-03-31 HU [[BR]]
    2003-03-20 RM [[BR]]
    2003-02-11 AW [[BR]]
    2003-01-10, 2003-01-17, 2003-02-05 RM [[BR]] 
    2003-01-14 TG [[BR]]
    2003-01-03, 06 HU [[BR]]
    2002-12-31 HU [[BR]]
    2002-12-21, 22 HU [[BR]]
    2002-12-19 RM [[BR]]
    2002-12-13, 14, 15, 16 HU [[BR]]
    2002-12-11 RM [[BR]]
    2002-12-05  TG [[BR]]
    2002-11-27 RM [[BR]]
    2002-11-05 AW [[BR]]
    2002-10-18 DJ [[BR]]
    2002-10-15 DJ [[BR]]
    2002-10-09, 12, 14 HU [[BR]]
    2002-10-08 AW [[BR]]
    2002-09-27 TG [[BR]]
    2002-09-26 DJ [[BR]]
    2002-09-23 AW [[BR]] 
    2002-09-11/12, 17 HU [[BR]]
    ... (?) [[BR]]
    2002-08-07,10 HU [[BR]]
    2002-07-22 DJ [[BR]]
    ... (?) [[BR]]
    2002-07-16  HU [[BR]]
    ... (?) [[BR]][[BR]]
+To see the changes between the actual and the last version, please see '''''Show Changes''''' in the Wiki Interface. 
If you want to see the Revision History of this page, please see '''''Get Info''''' in the Wiki Interface.
-Line 157:
+Line 131:
-'''Created by R. Mauersberger, June 18th, 2002'''
+== Legend ==

(./) : OK[[BR]]
/!\ : Warning[[BR]]
{X} : Error[[BR]]


The wiki markup of these icons is:

{{{(./) : OK
/!\ : Warning
{X} : Error
}}}

[#beginOfPage Back to top]