|
Size: 7396
Comment: .
|
Size: 7896
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 77: | Line 77: |
| 10:00-16:00[Raphaël]: Pointing Focus on f source 1418+546. Then observe project 082-25 (Source PSZ2G107) 2 rounds (2 hr). | 10:00-16:00[Raphaël]: Pointing Focus on f source 1418+546. Then observe project 082-25 (Source PSZ2G107) 2 rounds (2 hr). Making Skydip. Starting D01-M51 source. Changed to 47 Hz samplinng rate: 15/4/37 lost KIDs. @11:15 UT, Jean fixes a problem in the make-imbf. Yesterday the new make-imbf did not produce the imbf files of scan 20251021s171. we ran it manually, but the result was flawed. Jean fixed the manual version of the new make-imbf, that was looking for the Antenna traces in the wrong location. Thank you! The initial issue (that the automatic version did not produce the s171 files) is under investigation. |
Daily Reports (2025/10/21-28, NIKA2 run 75, Cryo run 87)
Observers on-site: Monica Rodriguez, Samuel Leclercq, Raphaël Maris, Stefano Berta and Stergios Amarantidis (AoD).
Remote observers: Michael Mattern (Saturday-Tuesday).
Operators: Sergio and Mario.
Shifts: 10-16 Raphaël; 16-22 Samuel; 22-4 Stefano; 4-10 Monica.
All times reported are in UTC (if not mentioned otherwise).
Preparatory notes
Please, remember to use the focus value of Ar1 (roughly Ar2 + 0.65 mm, but use directly the focus Ar1 monitor if possible). Please use the custom modified focus script focusOTF-Z_2025.pako.
Therefore, importantly, when checking the quality of the beam on a pointing map to decide if a new focus is needed, it is better to do it on the Ar1 map, because that's the one focused at best.
Project D01-25 (M51) requires DAQ restarting with the run87_newSweep_M51_tp.ini file. Come back to run87_neSweep_tp.ini after observing this project.
Please fill the Table with the Ar1,2,3 focus values as follows. At best, make one table per day.
Focus sequences
Scan nr
Target
Ar2
Ar1
Ar3
Notes
Similarly, if any beam maps are taken:
Beam maps (99 sub-scans)
Scan Nr
Target
Focus
Notes
October 21st, 2025, Tuesday
15:00-22:00[All]: Maintenance finished with no issues. DAQ started at 14:10 with 21/3/47 bad KIDS for arrays 1,2 and 3, respectively. Repeating the DAQ at 14:24 with 28/3/89. Trying to point at NGC7027 and MWC349 but the weather is too unstable (p2p~10-20Jy/beam), moving to K3-50A for pointing and focus (using the modified 2025 script). Moving for calib_1scan to MWC349, etc. Switching to project 053-25 (source 1803+784 is better for pointing/focus). One repetition of L1157B. Around 17:12 we moved to a skydip and then to the normal flux calibrators. After pointing/focus on 1803+784 we move to project 022-25. Two repetitions of Ceph-4.
22:00-04:00[Stefano]: here follows the evolution of the night:
- I let the 022-25 observations finish
- some difficulties in focusing properly, due to sky fluctuations combined with the big difference between Ar2 and Ar1
- 053-25 one repetition on L1157B (4 scans)
- calibrations (MWC349, CRL2688, NGC7027)
- 053-25 one more repetition on L1157B (4 scans)
- calibrations (Neptune, Uranus)
I decide not to take any beam maps on Uranus, because: a) the sky is not stable enough; b) in principle we'd need three beam maps, focused on each of the three NIKA2 arrays independently!
- @00:30 UT check in the cabin if anything is out of place, because NIKA2 is so unstable. All good. Nothing to report.
- some struggle to get a position with a decent stability, the wind is slowly rising and the humidity too.
- 066-25, one repetition of "M31-inner". tau(225) at start = 0.291.
Focus sequences of 2025/10/21
Scan nr
Target
Ar2
Ar1
Ar3
Notes
20251021s109-113
K3-50A
+0.10
+0.61
+0.80
Started at 1mm, custom script, array 2 out of range
114-118
K3-50A
+0.02
+0.60
+0.82
Started at 0.61mm, custom script
131-135
1803+784
...
+0.56
+0.75
Started at 0.6mm, custom script, array 2 out of range
147-151
1803+784
+0.15
+0.68 to +0.77
+1.00
Started at 0.56mm, custom script; focus set to 0.68
162-166
1803+784
+0.33
+1.10
...
Started at 0.8 mm, custom; Ar1 based on FWHM only; Ar3 out of range
167-171
1803+784
...
...
...
Started at 1.0mm; custom; problems with the new make-imbf of scan 171
172-176
1803+784
+0.16
+1.00
+1.24
Started at 1.0; custom; Ar2 not well determined; see Tapas for further interesting features of this sequence
187-191
MWC349
+0.45
+1.10
+1.25
Started at 1.0; custom; Ar3 not well sampled
208-211 + 20251022s1
Uranus
+0.45
+1.05
+1.18
Started at 1.1 mm; custom;
October 22nd, 2025, Wednesday
04:00-10:00[Monica]: Pointing, Focus and calib_1 scan in Uranus. Then project 066-25 (Source M31_inner) for 1 hr (1 round), weather started to became very unstable in the last scan peak to peak variations > 50 Jy/beam (Ar2). Then pointing and focus in Uranus, then the opacity rise to 1.0, so we stopped ~ 50 minutes. Continue with pointing, focus, pointing and calib_1scan in Uranus and Alfori. Then observe project 082-25 (Source PSz2G107) 2 rounds (~ 2hr).
10:00-16:00[Raphaël]: Pointing Focus on f source 1418+546. Then observe project 082-25 (Source PSZ2G107) 2 rounds (2 hr). Making Skydip. Starting D01-M51 source. Changed to 47 Hz samplinng rate: 15/4/37 lost KIDs.
@11:15 UT, Jean fixes a problem in the make-imbf. Yesterday the new make-imbf did not produce the imbf files of scan 20251021s171. we ran it manually, but the result was flawed. Jean fixed the manual version of the new make-imbf, that was looking for the Antenna traces in the wrong location. Thank you! The initial issue (that the automatic version did not produce the s171 files) is under investigation.
16:00-22:00[Samuel]: ...
22:00-04:00[Stefano]: ...
Focus sequences of 2025/10/22
Scan nr
Target
Ar2
Ar1
Ar3
Notes
19-23
Uranus
0.5
1.25
1.84
Started at 1.03 mm Focus optimized for Ar1; custom script
35-39
Uranus
0.5
1.18
1.44
Started at 1.25 mm, focus optimized for Ar1; custom script
42-46
Uranus
+0.45
+1.19
+1.47
Started at 1.18 mm. optimized for Ar1; custom script
52-56
ALFORI
+033
+1.1
+1.32
Started at 1.19 mm optimized for Ar1; custom script
61-65
Uranus
+0.35
+1.12
+1.33
Started at 1.1 mm optimized for Ar1; custom script
81-85
1418+546
+0.19
+1.1
+1.3
Started at 1.12 mm optimized for Ar1; custom script
October 23rd, 2025, Thursday
04:00-10:00[Monica]: ...
10:00-16:00[Raphaël]: ...
16:00-22:00[Samuel]: ...
22:00-04:00[Stefano]: ...
Focus sequences
Scan nr
Target
Ar2
Ar1
Ar3
Notes
October 24th, 2025, Friday
04:00-10:00[Monica]: ...
10:00-16:00[Raphaël]: ...
16:00-22:00[Samuel]: ...
22:00-04:00[Stefano]: ...
Focus sequences
Scan nr
Target
Ar2
Ar1
Ar3
Notes