Differences between revisions 13 and 185 (spanning 172 versions)
⇤ ← Revision 13 as of 2008-08-30 20:03:24 →
Size: 3798
Editor: 24
Comment:
← Revision 185 as of 2009-02-05 10:52:29 → ⇥
Size: 14845
Editor: visitor3
Comment:
Deletions are marked like this. Additions are marked like this.
Line 3: Line 3:
Line 8: Line 7:
This page summarizes the present instrumentation at the 30m observatory. The current status is described on another
[http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus page]. 
 		 This page summarizes the '''present instrumentation''' installed at the 30m observatory. [[BR]] The current system '''status''' is described [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus on a second page].
Line 15: Line 13:
==== A,B,C,D single pixel receivers ====
A maximum of four receivers, from the total of eight, can be used simultaneously. The following table summarizes the allowed combinations and some of the most important receiver characteristics. Plots of the receiver characteristics.
Line 18: Line 14:
==== HERA 3x3 dual-polarisation 1.2mm array ====
HERA cannot be combined with other receivers; up to now not all frequencies have been pretuned. Hera has 18 pixels separated by 24". Local contact for HERA: Albrecht Sievers		  * Eight single pixel receivers A,B,C,D, and the 3x3 dual-polarisation HERA receiver are installed in the [http://www.iram.es/IRAMES/telescope/telescopeSummary/receiver6.html receiver cabin].
Line 21: Line 16:
Table  * Four of the 8 A,B,C,D receivers can be used simultaneously. HERA cannot be combined with other receivers.
Line 23: Line 18:
 1. Using a special external LO, frequencies down to 77 GHz can be measured with good sideband rejection. For frequencies below 77 GHz, the sideband recection becomes weaker, and the sideband ratio reaches unity at 72 GHz ||'''Rx''' ||#||'''Pol'''|||||||||| '''Rx combinations''' ||'''tuning range''' || '''Trx''' || '''IF''' || '''IF Bw''' || '''Gim''' || '''Rem.''' ||
|| || || || '''AB''' || '''CD''' || '''AD''' || '''BC''' || ||'''[GHz]''' || '''[K]''' || '''[GHz]''' || '''[GHz]''' || '''[dB]''' || ||
||A100 || 1|| V || X || || X || || ||(72-)80.0-115.5 || 60-80 || 1.5 || 0.5 || >20 || '''1. '''||
||B100 || 1|| H || X || || || X || ||(72-)81.0-115.5 || 60-85 || 1.5 || 0.5 || >20 || '''1.'''||
||C150 || 1|| V || || X || || X || ||130-183 || 70-125 || 4 || 1 || 15-25 || ||
||D150 || 1|| H || || X || X || || ||130-183 || 80-125 || 4 || 1 || 08-17 || ||
||A230 || 1|| V || X || || X || || ||197-266 || 85-150 || 4 || 1 || 12-17 || ||
||B230 || 1|| H || X || || || X || ||197-266 || 95-160 || 4 || 1 || 12-17 || ||
||C270 || 1|| V || || X || || X || ||241-281 || 125-250 || 4 || 1 || 10-20 || '''2.'''||
||D270 || 1|| H || || X || X || || ||241-281 || 150-250 || 4 || 1 || 9-13 || '''2.'''||
||HERA1 || 9|| H || || || || || X || 215-272 || 110-380 || 4 || 1 || ~10 || '''2.,3.'''||
||HERA2 || 9|| V || || || || || X || 215-241 || 120-340 || 4 || 1 || ~10 || '''2.,3.'''||

 * [http://www.iram.es/IRAMES/groups/receiver/receiver.html More information on the heterodyne receivers.]

 
'''Remarks:'''

 1. Using a special external LO, frequencies down to 77 GHz can be measured with good sideband rejection. For frequencies below 77 GHz, the sideband recection becomes weaker, and the sideband ratio reaches unity at 72 GHz. [http://www.iram.fr/IRAMFR/PV/lowfreqs/report.ps.gz Test report of 2004], [http://www.iram.fr/IRAMFR/PV/lowfreqs/spectra.html Test spectra]
Line 27: Line 40:
 1. 2x(3x3) pixel receiver with a 24" separation of the pixels. Equipped with a derotator allowing to follow a source in the sky maintaining the same "footprint".  1. HERA is a heterodyne receiver array consisting of two arrays of 3x3 pixels with 24" spacing. The two arrays have orthogonal polarization (V, H) the two polarizations pointing at identical locations on the sky. HERA is equipped with a derotator allowing to follow a source in the sky maintaining the same "footprint". The tunable range is between 215 and 272 GHz. In this range the beamwidth varies between 12" and 9".

  * [http://www.iram.es/IRAMES/otherDocuments/manuals/HERA_manual_v20.pdf HERA manual, version 2.0] by Schuster et al. 2006

  * [http://esoads.eso.org/abs/2004A%26A...423.1171S Schuster et al. 2004, A&A, 423, 1171] A 230 GHz Heterodyne Receiver Array for the IRAM 30m telescope ([http://www.iram.es/IRAMES/otherDocuments/manuals/0179hera.pdf local copy])

[#beginOfPage Back to top]
Line 31: Line 50:
Table Two large field bolometer cameras are installed: '''MAMBO1''' with 37 pixels, and '''MAMBO2''' with 117 pixels ([http://www.mpifr-bonn.mpg.de/div/bolometer/#mamgo MAx-Planck Millimeter BOlometer Array]). Usually MAMBO2 is in use. Both cameras work at 1.2mm wavelength, the HPBW is 11", pixel spacing is 20", and the sensitivity is 1.5mJy. This is the rms after 10 minutes integration (normal bolometric conditions) with skynoise removal. See [http://www.iram.es/IRAMES/mainWiki/MamboWebPage the MAMBO page for details.]
Line 33: Line 52:
local contact for bolometers: Stephane Leon [#beginOfPage Back to top]
Line 35: Line 54:
  == Efficiencies and Half-power beam width == == Telescope efficiencies and beam widths ==
Line 38: Line 56:
Below you find the most recent values for the forward and beam efficiencies. We have also compiled the value of the efficiencies in the past .  * Below you find the forward and beam efficiencies upto 280 GHz measured in March 2005 ([http://www.iram.fr/IRAMFR/ARN/aug05/node6.html IRAM Newsletter 8/05]). Values above 300 GHz are predictions based on the observations compiled in the IRAM Annual Report 2007 attachment:IRAM_2007.pdf ).
Line 40: Line 58:
Here you can find the plot with the most recently measured beam efficiencies.  || '''freq''' || '''HPBW''' || '''Beff''' || '''Aeff''' || '''S/TA*''' || '''Feff''' || '''Comments''' ||
 || '''(GHz)''' || '''(arcsec)''' || '''(%)''' || '''(%)''' || '''(Jy/K)''' || '''(%)''' || ||
 || || (1) || (2) || (3) || (4) || (5) || (6) ||
 ||72 (extrapolated) || 34 || 79 || || 6.0 || 95 || ||
 ||77 (extrapolated) || 32 || 79 || || 6.0 || 95 || ||
 ||86 || 29 || 78 || || 6.0 || 95 || ||
 ||110 || 22 || 75 || || 6.3 || 95 || ||
 ||145 || 17 || 69 || || 6.7 || 93 || ||
 ||170 || 14.5 || 65 || || 7.1 || 93 || ||
 ||210 || 12 || 57 || || 7.9 || 91 || ||
 ||235 || 10.5 || 52 || || 8.7 || 91 || ||
 ||260 || 9.5 || 46 || || 9.5 || 88 || ||
 ||279 || 9 || 42 || ||10.4 || 88 || ||
 ||310 || 7.9 || || 37 || || || predicted ||
 ||345 || 7.1 || || 32 || || || predicted ||
 ||360 || 6.8 || || 30 || || || predicted ||
Line 42: Line 75:
Table  1. The '''half power beam width, HPBW''', can be well fitted by: HPBW/arcsec = 2460/freq/GHz.
Line 44: Line 77:
1) The HPBW can be well fit by: HPBW('') = 2460/freq(GHz).  1. '''Main beam efficiency Beff'''. The data can be well fit by a Ruze function Beff = 1.2 epsilon exp[-(4pi R sigma/ lambda)^2] with sigma being the rms value of the telescope optics deformations, R the reduction factor for a steep main reflector, epsilon the aperture efficieny of the perfect telescope and lambda the wavelength in mm. The data can be fit by R*sigma = 0.07 and epsilon = 0.69.
Line 46: Line 79:
2) The data can be well fit by a Ruze function B_eff = 1.2 epsilon exp[-(4pi R sigma/ lambda)^2] with sigma being the rms value of the telescope optics deformations, R the reduction factor for a steep main reflector, epsilon the aperture efficieny of the perfect telescope and lambda the wavelength in mm. The data can be fit by R*sigma = 0.07 and epsilon = 0.69. The aperture efficiency of the 30-m telescope can be obtained using eta_a=B_eff*0.79  1. '''Aperture efficiency, Aeff''' The aperture efficiency of the 30-m telescope can be obtained using Aeff=Beff*0.79
Line 48: Line 81:
3) For a Gaussian source and beam size, and a source which is much smaller than the beam, S(Jy)/T_mb(K)=8.18E-7*theta(")^2*nu(GHz)^2 (Rohlfs & Wilson, Tools of Radioastronomy (2. ed., Eq. 8.20). Using the approximation in 1) yields for the 30-m telescope S/T_mb=4.95 Jy/K. S/T_A* is obtained by multiplying 4.95 J/K with F_eff/B_eff  1. '''Point source sensitivity S/T_A*.''' For a Gaussian source and beam size, and a source which is much smaller than the beam, S(Jy)/T_mb(K)=8.18E-7*theta(")**2*nu(GHz)**2 (Rohlfs & Wilson, Tools of Radioastronomy (2. ed., Eq. 8.20). Using the approximation in 1) yields for the 30m telescope S/T_mb=4.95 Jy/K. S/T_A* is obtained by multiplying 4.95 J/K with Feff/Beff.
Line 50: Line 83:
Table  1. '''Gain-elevation curves.''' The most recent curves are given in the IRAM Annual Report 2007 attachment:IRAM_2007.pdf
Line 52: Line 85:
4) The values for F_eff are valid after the 12th of December 2000 when a new reflecting ring was put around the secondary mirror. The moon efficiencies are equal to forward efficiencies (Kramer et al. 1997).  1. '''Forward efficiency Feff''': The values for Feff are valid after the 12th of December 2000 when a new reflecting ring was put around the secondary mirror. Forward efficiencies are derived from skydips.

 1. '''Error beam''': A part of the power pattern is distributed in an error beam, which can be approximated by three Gaussians. Astronomers should take this into account when converting antenna temperatures to brightness temperatures, especially when mapping extended sources.

 1. Historic values: [http://www.iram.es/IRAMES/telescope/telescopeSummary/beam_effis.html Plot of efficiencies against frequency, measured in 2000], [http://www.iram.es/IRAMES/telescope/telescopeSummary/effi_history.html Compilation of efficiencies obtained in the past till 2001].

[#beginOfPage Back to top]
Line 55: Line 94:
=== Spectrometers ===
Line 57: Line 95:
Table || || Type || Channel Width || Bandwidth || Receiver (width mode) || Remark ||
|| '''1 MHz''' || Filterbank || 1 MHz || 4x256 MHz, 2x512 MHz, or, 1x1GHz || A100, B100 (narrow), A230, B230, C150, D150, C270, D270 (narrow or wide) || (1) ||
|| '''4 MHz''' || Filterbanks || 4 MHz || 9x1GHz || either HERA1 or HERA2 (wide), all other SIS receivers (wide) except 3mm || (2) ||
|| '''WILMA''' || Autocorrelator || 2 MHz || 18x930 MHz || HERA (wide) || (3) ||
|| '''VESPA''' || Autocorrelator || 3.3 kHz-1.25 MHz || 10-512 MHz || all SIS receives incl. HERA (narrow) || (4) ||
|| '''XPOL''' || VESPA || 40kHz-1.25MHz || 120-640MHz || A100 and B100 (narrow) || (5) ||
|| '''ABBA''' || || || || || (6) ||
Line 59: Line 103:
=== Bolometer backends === In general, several backends can be attached to one receiver. Exceptions are listed below. The [http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf pako manual] describes in detail how to configure the backends.
Line 61: Line 105:
== Spectral Line Observing Modes ==  1. '''1MHz Filterbank''': max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver.
Line 63: Line 107:
 * '''Position switching''': only relative OFF positions possible (radio projection offsets).  1. '''4MHz Filterbank''': max. 9 parts; use of the 4MHz filterbank excludes the use of VESPA on the same receiver. Frequency switching not available. While the channel spacing is 4MHz, the 3dB width is 5.4MHz and the noise equivalent width is 6.5 MHz
Line 65: Line 109:
 * '''Wobbling secondary''': max. 240" throw at 0.25 Hz, standard phase duration 0.5 Hz.  1. '''WILMA''': [http://www.iram.fr/IRAMFR/TA/backend/veleta/wilma/index.htm The Wideband Line Multiple Autocorrelator] for HERA
Line 67: Line 111:
 * '''Frequency switching''': max. 45 km/s throw at max. 0.5 Hz., with 100 kHz filters and autocorrelator only  1. '''VESPA''': [http://www.iram.fr/IRAMFR/TA/backend/veleta/vespa/index.htm The Versatile SPectrometer Array]. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); [http://www.iram.es/IRAMES/otherDocuments/manuals/vespa_ug.ps VESPA User Guide (2002)], [http://www.iram.es/IRAMFR/ARN/dec02/node6.html Summary in IRAM Newsletter No. 54 (Dec 2002)], local contact: G. Paubert
Line 69: Line 113:
 * '''On the fly mapping''': Works with all receiver and backends, typical dump rate 0.5-1 Hz  1. '''XPOL''': Line and continuum polarimetry is possible at the 30m using a new type of IF polarimeter designated XPOL. The central feature of XPOL is the correlator VESPA where the IF signals from two orthogonally polarized receivers are cross correlated to determine the four Stokes parameters. A manual is in preparation, contact: C. Thum
Line 71: Line 115:
 1. '''ABBA1 and ABBA2''' (Adc Bolometer Backend) are the bolometer backends, i.e. dedicated PCs connected to the bolometers.


[#beginOfPage Back to top]

== Control System ==

The 30-m telescope runs under the New Control System (NCS), see:

 . [http://www.iram.es/IRAMES/ncs30m/ NCS documentation] [http://mrt-lx1/mainWiki/ Wiki with up-to-date Notes on NCS]
Observing modes and source offsets in:

 * Projection "Radio" (same offsets as in old CS) in Equatorial J2000.0
 * "true angle" horizontal
 * Nasmyth (receiver offsets)

[#beginOfPage Back to top]

== Observing Modes and Switching Modes ==

|| Observing mode || swTotal || swBeam || swWobbler || swFrequency ||
|| '''Calibrate''' (Heterodyne) || X || || || ||
|| '''Pointing''' || X || X || X || ||
|| '''Focus''' || X || X || X || ||
|| '''Tip''' (Skydip) || X || || || ||
|| '''Track''' || || || || fsw ||
|| '''ONOFF''' || psw || || wsw || ||
|| '''OTFMAP''' (Heterodyne) || otf/psw || || || otf/fsw ||
|| '''Raster''' || || || || ||
|| '''OTFMAP''' (MAMBO Bolometer) || || || X || ||
|| '''VLBI''' || X || || || ||

 * for more details on observing and switching modes, see the section "NCS explained" in the [http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf pako cookbook]


 * '''swTotal''' stands for total power observations without switching, while still using the internal synchronization signals.
 * '''swBeam''' beam switched observations using the chopper wheel on mirror M4.
 * '''swWobbler''' switching the wobbling secondary (M2). The maximum allowed throw is +/-2'.
 * '''swFrequency''' switching the local oscillator frequency

 * '''Pointing''': Using nearby (within 10 degree) pointing sources, <1" accuracy can be obtained; with absolute ("blind") pointing, the accuracy is about 2" rms, the receivers are aligned within 1.7" (see the [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus Telescope Status page] for current values). Checking the pointing and alignment (using e.g. a planet) is the responsibility of the observer.
 * '''Focus''': residual errors of <1mm may need correction. There are systematic differences of upto 0.6mm in the focus of the different receivers (cf. [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus Telescope Status page]). The focus is subject to change especially during sunrise and sunset.
 * '''Position switching (psw)''': the combination of ONOFF with swTotal is called "Position Switching". Only relative off-source reference positions are possible.
 * '''Wobbler switching (wsw)''': often called '''double beam switching mode''': max. 240" throw at 0.25 Hz, standard phase duration 0.5 Hz.
 * '''Frequency switching (fsw)''': max. 45 km/s throw up to about 10 Hz.
 * '''On the fly mapping (Heterodyne)''': Works with all receivers and backends, typical dump rate 0.5 to 10 Hz. ''OTF can be observed without reference position, e.g. for galaxies, and MIRA is able to use emission-free OTF data as reference!''
 * '''Raster mapping''' is at present '''not offered'''. The observer may want to use eigher psw or otf instead.
Line 72: Line 163:
  [#beginOfPage Back to top]
Line 73: Line 166:
 * '''Pointing''': Using nearby (within 10 degree) pointing sources, <1" accuracy can be obtained; with absolute ("blind") pointing, the accuracy is <4", the receivers are usually aligned within 2". Checking the pointing and alignment (using e.g. a planet) is the responsibility of the observer. == Weather station and Taumeter ==
Line 75: Line 168:
 * '''Focus''': residual errors of <1mm may need correction. There may be systematic differences (<0.4") in the focus of the different receivers. Check focus at least at after sunrise and sunset.  * [http://mrt-lx3.iram.es/tau/meteo-main.php Weather station]
  *Wind velocity and direction measured on hill behind the telescope
  * Outside temperature and relative humidity measured at base of telescope. In case the sensors are frozen, the operator will use a mobile weather station and enter values by hand into the drive program.
  * Pressure measured at entrance to control building

 * [http://mrt-lx3.iram.es/tau/taumeter-main-db.php Taumeter] does regular skydips to inform the observer about the sky transmission near '''225 GHz'''. The local oscillator works at 225GHz. The IF is 1.5GHz and the bandwidth is 0.5GHz. It is a double-sideband Schottky receiver.

[#beginOfPage Back to top]

Old [http://www.iram.es/IRAMES/telescope/telescopeSummary/telescope_summary.html Telescope System Summary page of September 07]

This is page http://www.iram.es/IRAMES/mainWiki/TelescopeSystemSummary moderated by Carsten Kramer

Anchor(beginOfPage)

This page summarizes the present instrumentation installed at the 30m observatory. BR The current system status is described [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus on a second page].

TableOfContents(4)

Frontends

Heterodyne Receivers

Rx

#

Pol

Rx combinations

tuning range

Trx

IF

IF Bw

Gim

Rem.

AB

CD

AD

BC

[GHz]

[K]

[GHz]

[GHz]

[dB]

A100

1

V

X

X

(72-)80.0-115.5

60-80

1.5

0.5

>20

1.

B100

1

H

X

X

(72-)81.0-115.5

60-85

1.5

0.5

>20

1.

C150

1

V

X

X

130-183

70-125

4

1

15-25

D150

1

H

X

X

130-183

80-125

4

1

08-17

A230

1

V

X

X

197-266

85-150

4

1

12-17

B230

1

H

X

X

197-266

95-160

4

1

12-17

C270

1

V

X

X

241-281

125-250

4

1

10-20

2.

D270

1

H

X

X

241-281

150-250

4

1

9-13

2.

HERA1

9

H

X

215-272

110-380

4

1

~10

2.,3.

HERA2

9

V

X

215-241

120-340

4

1

~10

2.,3.

Remarks:

  1. Using a special external LO, frequencies down to 77 GHz can be measured with good sideband rejection. For frequencies below 77 GHz, the sideband recection becomes weaker, and the sideband ratio reaches unity at 72 GHz. [http://www.iram.fr/IRAMFR/PV/lowfreqs/report.ps.gz Test report of 2004], [http://www.iram.fr/IRAMFR/PV/lowfreqs/spectra.html Test spectra]

  2. Noise increasing with frequency
  3. HERA is a heterodyne receiver array consisting of two arrays of 3x3 pixels with 24" spacing. The two arrays have orthogonal polarization (V, H) the two polarizations pointing at identical locations on the sky. HERA is equipped with a derotator allowing to follow a source in the sky maintaining the same "footprint". The tunable range is between 215 and 272 GHz. In this range the beamwidth varies between 12" and 9".

[#beginOfPage Back to top]

Bolometers

Two large field bolometer cameras are installed: MAMBO1 with 37 pixels, and MAMBO2 with 117 pixels ([http://www.mpifr-bonn.mpg.de/div/bolometer/#mamgo MAx-Planck Millimeter BOlometer Array]). Usually MAMBO2 is in use. Both cameras work at 1.2mm wavelength, the HPBW is 11", pixel spacing is 20", and the sensitivity is 1.5mJy. This is the rms after 10 minutes integration (normal bolometric conditions) with skynoise removal. See [http://www.iram.es/IRAMES/mainWiki/MamboWebPage the MAMBO page for details.]

[#beginOfPage Back to top]

Telescope efficiencies and beam widths

  • Below you find the forward and beam efficiencies upto 280 GHz measured in March 2005 ([http://www.iram.fr/IRAMFR/ARN/aug05/node6.html IRAM Newsletter 8/05]). Values above 300 GHz are predictions based on the observations compiled in the IRAM Annual Report 2007 attachment:IRAM_2007.pdf ).

    freq

    HPBW

    Beff

    Aeff

    S/TA*

    Feff

    Comments

    (GHz)

    (arcsec)

    (%)

    (%)

    (Jy/K)

    (%)

    (1)

    (2)

    (3)

    (4)

    (5)

    (6)

    72 (extrapolated)

    34

    79

    6.0

    95

    77 (extrapolated)

    32

    79

    6.0

    95

    86

    29

    78

    6.0

    95

    110

    22

    75

    6.3

    95

    145

    17

    69

    6.7

    93

    170

    14.5

    65

    7.1

    93

    210

    12

    57

    7.9

    91

    235

    10.5

    52

    8.7

    91

    260

    9.5

    46

    9.5

    88

    279

    9

    42

    10.4

    88

    310

    7.9

    37

    predicted

    345

    7.1

    32

    predicted

    360

    6.8

    30

    predicted

  • The half power beam width, HPBW, can be well fitted by: HPBW/arcsec = 2460/freq/GHz.

  • Main beam efficiency Beff. The data can be well fit by a Ruze function Beff = 1.2 epsilon exp[-(4pi R sigma/ lambda)^2] with sigma being the rms value of the telescope optics deformations, R the reduction factor for a steep main reflector, epsilon the aperture efficieny of the perfect telescope and lambda the wavelength in mm. The data can be fit by R*sigma = 0.07 and epsilon = 0.69.

  • Aperture efficiency, Aeff The aperture efficiency of the 30-m telescope can be obtained using Aeff=Beff*0.79

  • Point source sensitivity S/T_A*. For a Gaussian source and beam size, and a source which is much smaller than the beam, S(Jy)/T_mb(K)=8.18E-7*theta(")**2*nu(GHz)**2 (Rohlfs & Wilson, Tools of Radioastronomy (2. ed., Eq. 8.20). Using the approximation in 1) yields for the 30m telescope S/T_mb=4.95 Jy/K. S/T_A* is obtained by multiplying 4.95 J/K with Feff/Beff.

  • Gain-elevation curves. The most recent curves are given in the IRAM Annual Report 2007 attachment:IRAM_2007.pdf

  • Forward efficiency Feff: The values for Feff are valid after the 12th of December 2000 when a new reflecting ring was put around the secondary mirror. Forward efficiencies are derived from skydips.

  • Error beam: A part of the power pattern is distributed in an error beam, which can be approximated by three Gaussians. Astronomers should take this into account when converting antenna temperatures to brightness temperatures, especially when mapping extended sources.

  • Historic values: [http://www.iram.es/IRAMES/telescope/telescopeSummary/beam_effis.html Plot of efficiencies against frequency, measured in 2000], [http://www.iram.es/IRAMES/telescope/telescopeSummary/effi_history.html Compilation of efficiencies obtained in the past till 2001].

[#beginOfPage Back to top]

Backends

Type

Channel Width

Bandwidth

Receiver (width mode)

Remark

1 MHz

Filterbank

1 MHz

4x256 MHz, 2x512 MHz, or, 1x1GHz

A100, B100 (narrow), A230, B230, C150, D150, C270, D270 (narrow or wide)

(1)

4 MHz

Filterbanks

4 MHz

9x1GHz

either HERA1 or HERA2 (wide), all other SIS receivers (wide) except 3mm

(2)

WILMA

Autocorrelator

2 MHz

18x930 MHz

HERA (wide)

(3)

VESPA

Autocorrelator

3.3 kHz-1.25 MHz

10-512 MHz

all SIS receives incl. HERA (narrow)

(4)

XPOL

VESPA

40kHz-1.25MHz

120-640MHz

A100 and B100 (narrow)

(5)

ABBA

(6)

In general, several backends can be attached to one receiver. Exceptions are listed below. The [http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf pako manual] describes in detail how to configure the backends.

  1. 1MHz Filterbank: max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver.

  2. 4MHz Filterbank: max. 9 parts; use of the 4MHz filterbank excludes the use of VESPA on the same receiver. Frequency switching not available. While the channel spacing is 4MHz, the 3dB width is 5.4MHz and the noise equivalent width is 6.5 MHz

  3. WILMA: [http://www.iram.fr/IRAMFR/TA/backend/veleta/wilma/index.htm The Wideband Line Multiple Autocorrelator] for HERA

  4. VESPA: [http://www.iram.fr/IRAMFR/TA/backend/veleta/vespa/index.htm The Versatile SPectrometer Array]. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); [http://www.iram.es/IRAMES/otherDocuments/manuals/vespa_ug.ps VESPA User Guide (2002)], [http://www.iram.es/IRAMFR/ARN/dec02/node6.html Summary in IRAM Newsletter No. 54 (Dec 2002)], local contact: G. Paubert

  5. XPOL: Line and continuum polarimetry is possible at the 30m using a new type of IF polarimeter designated XPOL. The central feature of XPOL is the correlator VESPA where the IF signals from two orthogonally polarized receivers are cross correlated to determine the four Stokes parameters. A manual is in preparation, contact: C. Thum

  6. ABBA1 and ABBA2 (Adc Bolometer Backend) are the bolometer backends, i.e. dedicated PCs connected to the bolometers.

[#beginOfPage Back to top]

Control System

The 30-m telescope runs under the New Control System (NCS), see:

Observing modes and source offsets in:

  • Projection "Radio" (same offsets as in old CS) in Equatorial J2000.0
  • "true angle" horizontal
  • Nasmyth (receiver offsets)

[#beginOfPage Back to top]

Observing Modes and Switching Modes

Observing mode

swTotal

swBeam

swWobbler

swFrequency

Calibrate (Heterodyne)

X

Pointing

X

X

X

Focus

X

X

X

Tip (Skydip)

X

Track

fsw

ONOFF

psw

wsw

OTFMAP (Heterodyne)

otf/psw

otf/fsw

Raster

OTFMAP (MAMBO Bolometer)

X

VLBI

X

  • for more details on observing and switching modes, see the section "NCS explained" in the [http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf pako cookbook]

  • swTotal stands for total power observations without switching, while still using the internal synchronization signals.

  • swBeam beam switched observations using the chopper wheel on mirror M4.

  • swWobbler switching the wobbling secondary (M2). The maximum allowed throw is +/-2'.

  • swFrequency switching the local oscillator frequency

  • Pointing: Using nearby (within 10 degree) pointing sources, <1" accuracy can be obtained; with absolute ("blind") pointing, the accuracy is about 2" rms, the receivers are aligned within 1.7" (see the [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus Telescope Status page] for current values). Checking the pointing and alignment (using e.g. a planet) is the responsibility of the observer.

  • Focus: residual errors of <1mm may need correction. There are systematic differences of upto 0.6mm in the focus of the different receivers (cf. [http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus Telescope Status page]). The focus is subject to change especially during sunrise and sunset.

  • Position switching (psw): the combination of ONOFF with swTotal is called "Position Switching". Only relative off-source reference positions are possible.

  • Wobbler switching (wsw): often called double beam switching mode: max. 240" throw at 0.25 Hz, standard phase duration 0.5 Hz.

  • Frequency switching (fsw): max. 45 km/s throw up to about 10 Hz.

  • On the fly mapping (Heterodyne): Works with all receivers and backends, typical dump rate 0.5 to 10 Hz. OTF can be observed without reference position, e.g. for galaxies, and MIRA is able to use emission-free OTF data as reference!

  • Raster mapping is at present not offered. The observer may want to use eigher psw or otf instead.

  • Polarimetry: using VESPA as an IF polarimeter

[#beginOfPage Back to top]

Weather station and Taumeter

  • [http://mrt-lx3.iram.es/tau/meteo-main.php Weather station]

    • Wind velocity and direction measured on hill behind the telescope
    • Outside temperature and relative humidity measured at base of telescope. In case the sensors are frozen, the operator will use a mobile weather station and enter values by hand into the drive program.
    • Pressure measured at entrance to control building

  • [http://mrt-lx3.iram.es/tau/taumeter-main-db.php Taumeter] does regular skydips to inform the observer about the sky transmission near 225 GHz. The local oscillator works at 225GHz. The IF is 1.5GHz and the bandwidth is 0.5GHz. It is a double-sideband Schottky receiver.

[#beginOfPage Back to top]

Old [http://www.iram.es/IRAMES/telescope/telescopeSummary/telescope_summary.html Telescope System Summary page of September 07]

This is page http://www.iram.es/IRAMES/mainWiki/TelescopeSystemSummary moderated by Carsten Kramer

TelescopeSystemSummary (last edited 2009-07-07 13:46:21 by visitor4)