Useful information for observations: List of astronomical Target, Pako scripts, Real Time Analysis, Observing strategies

List of Astronomical Target for Nika January 2014 run7

FXD: First version (8 Jan 2014)

Back to the NIKA run7 page

The nominal NIKA frequencies for this run are 260 and 150 GHz (ie 1.15 and 2.00 mm).

References and results are written in this private page

1. Planets and Asteroids

Mars, Uranus, Neptune for photometric calibration (primary calibrators) and focal plane geometry.

(Venus, Jupiter, Saturn) too hot too big

Here are the ephemeris for all planets The near and far sidelobes could be measured with Jupiter and Saturn.

2. Usual bright quasars, secondary calibrators and strong galactic sources (end of the list is dedicated to polarisation)

• for image quality, linearity checks, and pointing sessions

Bright source selection

Here is IRAM report on Secondary Calibrators

3. Weak Galactic sources

• for photometric calibration checks

Weak galactic sources

4. External extended galaxies

• for Science demonstration (mapping)

Nearby galaxies

5. High redshift sources

• for Science demonstration (sensitivity)

Distant galaxies

Here is the full detailed formatted list Full list v1 with fluxes

Here is the catalog for Pako has to be RENAMED to NIKA2014R7.sou on the pako computer

Here is a list of IRAM pointing sources with fluxes at 3mm and 2mm (I miss fluxes at 1mm, SL) FluxForPointingSources

Interface with the telescope: Pako

Short manual on useful "Pako for Nika" see on Granada computers 2013_docs_for_observations/Pako_helpv15.txt

- Pako scripts are in the Pako subdirectory

- Before starting the pointing session, we may be requested to move the azimuth by 60deg to reset the inclinometer of the az axis.

- Always stay at more that 1 deg from the Sun. There are internal safeties that prevent the antenna to point to the Sun, but we may not get error messages.

- try to get sources uniformly distributed on the sky, hence give priority to high elevation sources that are usually harder to reach.

- Do one focus at the beginning. No need to do more focus than one every 2-3hours.

The antenna can point between 60 and 460 degrees in azimuth, between 20 and 80 degrees in elevation.

- If a source is available both at low and high azimuth, use command SET TOPO LOW (or SET TOPO HIGH) to stay on the source without moving.

- The minimum number of sources to observe for the pointing model is 15. 30 is good enough.

- the pointing sources should be observed on 'short' period, e.g. 3-4 hours to avoid daily pointing variations

Commissioning requirements

Abstract

We can consider using 40 hours to test, calibrate and commission the instrument. Procedures will be tested several times, which include Pointing (Cross), Focus, OTF_Geometry, Skydip, Lissajous, OTF_Map. Tests include tuning, auto-tuning, robustness of data acquisition. Photometric calibration includes planets and secondary calibrators. Skydip and Lissajous sequences need to be better tested than before. Other sequences should be straightforward. The plateau systematics will be investigated via the OTG_geometry sequences. Near sidelobes can be measured by doing 5x5 map of of Jupiter or Saturn and use Pf variable.

Detailed version (after discussions SL, FXD, RZ, NB, AB, AS, HU)

6/6/2013: SL update after review with RZ. 14/01/2014: Update for this run.

Before Tuesday 21:

• Alignment with laser. Then align mm axis by minimizing the background (manual adjustment of M5 with micrometric screws.

• Run pakoNIKA (paKo Revision v 1.1.14.1 2013-06-01) => the antenna mount drive slowRate will be set to 8 Hz for all observations (if needed to go back to 1Hz as previous runs: let the operator reboot vac1, then use pakoNIKA2012).

• Start with Run 6 pointing model. Determine ref pixels at 1 and 2 mm, and check zig-zag (synchronization): 1st cross + OTF_geometry on Uranus. Among few detectors at the center of the arrays choose the one at 1 mm that seems the best (but decide on a reference detector at 2mm that could be used alternatively for the pointing model session or in bad weather): set Nasmyth offset, and then do not change this value anymore, later when it is needed to adjust the pointing use only set offset.

Tuesday 21 - OTF_Geometry & Pointing model session:

• Cross + pointing Lissajous (do that systematically through this characterization run). Use set offset to correct the pointing (but not Nasmyth) of

the 1mm ref detector.

• Focus + Focus_Liss (idem). Set focus, then redo cross for check.
• Several OTF_geometry to characterize the Field of View Geometry, for reproducibility. Keep the 1mm reference pixel chosen on previous day. Subscans

steps for OTF_geometry must be ≤ 5" otherwise not enough oversampling at 1mm. Attention for the map sizes take the size requested + scan velocity x 2

seconds !

• Pointing session. Set Nasmyth to center of the 2mm reference detector. Light session is useless because risks of smearing in the images and loose too

much time afterward with the necessity of frequent pointings. However full session not much longer since it requires ~20 sources spread on the local sky

(30 sources is not really useful and start to take time). Keep constant Nasmyth offsets during all the session (can be changed latter during

observations if one want to center the map on another pixel), but do Pointing offsets always (otherwise pointing source may moves away from the

reference pixel and will kill the accuracy of the fit), typically if the pointing offset is > 5" repeat the scan after setting the new offset. This time

do the pointing session with cross scans and Lissajous (that is done when analyzing the cross), and followed by a cross after correction offset.

Fill the following table (Offset X and Offset Y are the the values entered in set offset):

• Skydips. Needed only to calibrate the total power coefficients (once fitted we will be able to calculate the total power in the line of sight at

anytime). One skydip (= 2 scans, 1 down 1 up) at the end of this session. Following days: ONE SKYDIP PER DAY, and one each time the power on the KIDs is

changed.

Wednesday 22 - Polar setup:

• OTF_geometry on Uranus during the whole session (with pointing and focus regularly).
• Skydip (measure extended instrumental polar).

Thursday 23 - Geom and Focus:

• Standard starting calibration sequence on Uranus: Cross, Pointing_Liss, Focus, Focus_Liss, Cross, OTF_geometry. TO DO EVERY DAY.
• Focus Geometry: do OTF_geometry with 3 different set focus values (find best focus for other pixels than only the reference): 1st on axis (Z) AND

lateral focus (X then Y) + repeat ==> At least 3x3x2 = 18 scan. Then several OTF on optimal 3D_focus.

• Photometric calibration on primary and secondary calibrators with Lissajous scans and small OTF maps (Az El and/or few RA DEC for testing). Some

secondary to observe: W3OH, K3-50A, MWC349, CRL2688, NGC7027, CepA, NGC7538. Bright quasar: 3C454.3, 3C84, OJ287, 3C111. Check geom: CygA, M82.

• Few weak sources if the time (and weather) allows (Lissajous): check sensitivity.

Friday 24 - Polar characterization:

• Planet and Quasar: (small) OTF and Lissajous.
• Possibly extended sources: CasA, Crab.

Saturday 25 - Validate integration time:

• Integrate on sources of medium to weak fluxes: WR147, IRC10420, some of the TAU sources (tbc), 4C05.19, APM08279, MM18423, PSS2322, SXDF, F10214.

Lissajous.

• Extended sources (OTF zigzag): CasA, Crab. Test various scan speed 10, 20, 30, 40, 50, 60 arcsec/s.
• Test RA DEC OTF scans: NGC891.

Sunday 26 - Polar extended:

• Extended sources from strong to weak: Crab, CasA, (Orion) KL, NGC7023NW (~1h per source).

Monday 27 - Backup:

• If one of the above has suffered then redo it, otherwise try deep field (SXDF).

Science case demonstration

None: this time this is a commissioning run only.

Status of observations

Current status of observationsRun6