Size: 5387
Comment:
|
Size: 5650
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 62: | Line 62: |
Pako> '''swwobbler -throw/2. throw/2.''' !''Setup the wobbler throw [shortcut to be added]'' [[BR]] | Pako> '''bsw throw''' !''Setup the wobbler throw'' [[BR]] |
Line 112: | Line 112: |
== List of Commands == || Command || Explanation || || || || || '''@wbolo''' !! Setup the default configuration and the commands || || '''bf''' || Perform a focus || || '''bt''' || Perform a bolotip at the current azimuth || || '''btaz''' ''az'' || Perform a bolotip at the azimuth az'' |
Bolometer's Observation
The most important commands of the old system have been adapted to the NCS. Here is a typical starting sequence for the bolometer.
Setup the Bolometer
Pako> @wbolo ! Mambo2, central pixel 53, short onoff (onf4), setup the bolometer commands
Sources Catalog
Pako> catalog source pool ! Setup the project source catalog BR Pako> catalog source ihet ! Setup the pointing/calibration source catalog
Pointing sources: J1419+240 not 1419+240. BR
Pako is cASe-SenSiTIve for the source names.
Skydip, pointing, skydip
Pako> bt !Skydip at the current azimuth+start
Every 2 hours in stable atmospheric condition.
Pako> p40 !Short pointing for weak sources+start BR Pako> p60 !Long pointing for strong sources+start BR Pako> set pointing azcor elcor !Correct the pointing with azcor and elcor. Correction from MOPSIC (@p or @psn for weak source)
Pako> bf BR Pako> start ! Start the focus BR Pako> set focus sfcz !Correct the focus with sfcz. Correction from MOPSIC (@f or @fsn for weak sources) BR Do a focus when atmospheric conditions are changing, typically after sunset/sunrise
Before an Onoff, be sure you are pointing with the right pixel (20).
Do a pointing before each Onoff or map if they are longer than 30 mn.
Calibration
Calibration on a [primary|secondary] calibrator
Pako> catalog source ihet BR Pako> source Calibrator_Name BR Pako> p60 BR Pako> set pointing azcor elcor BR Pako> onf4 ! Short Onoff integration (4 Subscans of 10 s) with central pixel 53
You may do a short onf4 after a normal pointing to monitor the pointing source flux.
Onoff and Map
Pako>onf 20 30 !Perform an on-off integration of 20 subscans of 60s with a wobbler throw of 30" BR Pako> @onf30 !Some project may have their own on-off macro
Don't try to make very long integration, you may loose the complete scan. In such a case use a loop.
Pako> bsw throw !Setup the wobbler throw BR Pako> bmap laz lel elstep azv !Setup an OTF map of laz azimuth length, lel elevation length, elstep elevation step and azv azimuth speed (arcsec/s). BR Pako> start !Start the map after you checked it is correct (it gives you the total integration time).
The speed should not be larger than ~8 arcsec/sec
NOTE: BR roff20 : set the pixel 20 for on-off (most sensitive one). BR roff53 : set the central pixel 53 (default with @wbolo) BR BR
Typical Bolo Session
A typical starting session could be as following:
Pako> @wbolo Pako> source Mars Pako> gain 2 ! special case for Mars, normal gain is 10 Pako> p60 Pako> bt !skydip Pako> p60 Pako> set pointing 2. -6. Pako> focus 1.1 Pako> start Pako> set focus -3.5 Pako> onf4 ! Measure the flux of Mars Pako> gain 10. Pako> @wbolo Pako> set project 175_05 Pako> catalog source ihet Pako> source J0854+201 ! Pointing source Pako> roff20 Pako> p40 Pako> set pointing 0.4 -6.4 Pako> onf4 ! Why not ? Pako> catalog source pool Pako> source 0927+2001 !Project source Pako> onf 20 35 ! Do an on-off integration of 20 subscans of 60s ! with a wobbler throw of 35¨. Pako> Ad Nauseam ...
The set project Proj_Id will be necessary until it is automatically included in the source catalog.
List of Commands
Command |
Explanation |
|| || ||
@wbolo !! Setup the default configuration and the commands |
|
bf |
Perform a focus |
bt |
Perform a bolotip at the current azimuth |
|| btaz az || Perform a bolotip at the azimuth az
Heterodyne observations are more complex in the sense there is much more options available. Since the NCS/Pako are still under heavy development, we give here a typical session. Some commands are the same that with bolometer observations. If the macros written by the PIs are not working ask the Pool coordinator or the AoD. Heterodyne Observation
Pako> @setup-186_05-1850 ! Setup the frequencies/receivers.
Tuning...
Pako> source Mars
Pako> pointing ! Check if continuum backends are set
Pako> start
Pako> set pointing -1. 2. ! The correction are given using the mira program
Pako> focus 2.0
Pako> start
Pako> set focus -2.2 ! The correction is given using the mira program
Pako> cata source ihet
Pako> source J2240+245 ! Pointing source
Pako> pointing
Pako> start
Pako> set point -1. 0.5
Pako> catalog source pool
Pako> source N821
Pako> @backends-186_05 ! maybe included in the following macro
Pako> @target-wsw-186_05
Number of Loops= 5 ! according the indications of the PI.
Pako> @setup-186_05-1850 ! Setup the continuum backend.
Pako> source J2240+245
Pako> pointing
Pako> start
Pako> set point -1. 0.5
Pako> catalog source pool
Pako> source N822
Pako> @backends-186_05
Pako> @target-wsw-186_05
Number of Loops= 5
Pako> Ad Nauseam ...