|
Size: 5277
Comment:
|
Size: 5458
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 3: | Line 3: |
| = Bolometer's Observation: = | = Bolometer's Observation = |
| Line 7: | Line 7: |
| == Setup the Bolometer: == Pako> '''@wbolo''' !'' Mambo2, central pixel 53, short onoff (@onf4)'' |
== Setup the Bolometer == Pako> '''@wbolo''' !'' Mambo2, central pixel 53, short onoff (onf4), setup the bolometer commands'' |
| Line 10: | Line 10: |
| == Sources Catalog: == | == Sources Catalog == |
| Line 15: | Line 15: |
| <!> Pako is ''case-sensitive'' for the source names. | <!> Pako is ''cASe-SenSiTIve'' for the source names. |
| Line 18: | Line 18: |
| == Skydip, pointing, skydip : == | == Skydip, pointing, skydip == |
| Line 30: | Line 30: |
| Pako> '''focus 1.1''' [[BR]] | Pako> '''bf''' [[BR]] |
| Line 41: | Line 41: |
| == Calibration: == | == Calibration == |
| Line 44: | Line 44: |
| Pako> '''catalog source ihet [[BR]] | Pako> '''catalog source ihet''' [[BR]] |
| Line 51: | Line 51: |
| <!> You may do a short @onf4 after a normal pointing to monitor the pointing source flux. | <!> You may do a short ''onf4'' after a normal pointing to monitor the pointing source flux. |
| Line 55: | Line 55: |
| == Onoff and Map: == | == Onoff and Map == |
| Line 57: | Line 57: |
| Pako>'''@onf 20 30''' !''Perform an on-off integration of '''20''' subscans of 60s with a wobbler throw of '''30"''' '' [[BR]] | Pako>'''onf 20 30''' !''Perform an on-off integration of '''20''' subscans of 60s with a wobbler throw of '''30"''' '' [[BR]] |
| Line 62: | Line 62: |
| Pako> '''bsw throw''' !''Setup the wobbler throw'' [[BR]] | |
| Line 70: | Line 70: |
| '''@roff20''' : set the pixel 20 for on-off (most sensitive one). [[BR]] '''@roff53''' : set the central pixel 53 (default with @wbolo) |
'''roff20''' : set the pixel 20 for on-off (most sensitive one). [[BR]] '''roff53''' : set the central pixel 53 (default with @wbolo) |
| Line 76: | Line 76: |
| == Typical Bolo Session: == | == Typical Bolo Session == |
| Line 83: | Line 83: |
| Pako> @p60 | Pako> p60 |
| Line 85: | Line 85: |
| Pako> @p60 | Pako> p60 |
| Line 90: | Line 90: |
| Pako> @onf4 ! Measure the flux of Mars | Pako> onf4 ! Measure the flux of Mars |
| Line 97: | Line 97: |
| Pako> @roff20 | Pako> roff20 |
| Line 100: | Line 100: |
| Pako> @onf4 ! Why not ? | Pako> onf4 ! Why not ? |
| Line 103: | Line 103: |
| Pako> @onf 20 35 ! Do an on-off integration of 20 subscans of 60s | Pako> onf 20 35 ! Do an on-off integration of 20 subscans of 60s |
| Line 112: | Line 112: |
| == List of Commands == | |
| Line 113: | Line 114: |
| = Heterodyne Observation: = | || Command |||| <bgcolor='#E0E0FF'> Explanation || || bf || Perform a focus || = Heterodyne Observation = |
Bolometer's Observation
The most important commands of the old system have been adapted to the NCS. Here is a typical starting sequence for the bolometer.
Setup the Bolometer
Pako> @wbolo ! Mambo2, central pixel 53, short onoff (onf4), setup the bolometer commands
Sources Catalog
Pako> catalog source pool ! Setup the project source catalog BR Pako> catalog source ihet ! Setup the pointing/calibration source catalog
Pointing sources: J1419+240 not 1419+240. BR Pako is cASe-SenSiTIve for the source names.
Skydip, pointing, skydip
Pako> bt !Skydip at the current azimuth+start
Every 2 hours in stable atmospheric condition.
Pako> p40 !Short pointing for weak sources+start BR Pako> p60 !Long pointing for strong sources+start BR Pako> set pointing azcor elcor !Correct the pointing with azcor and elcor. Correction from MOPSIC (@p or @psn for weak source)
Pako> bf BR Pako> start ! Start the focus BR Pako> set focus sfcz !Correct the focus with sfcz. Correction from MOPSIC (@f or @fsn for weak sources) BR Do a focus when atmospheric conditions are changing, typically after sunset/sunrise
Before an Onoff, be sure you are pointing with the right pixel (20). Do a pointing before each Onoff or map if they are longer than 30 mn.
Calibration
Calibration on a [primary|secondary] calibrator
Pako> catalog source ihet BR Pako> source Calibrator_Name BR Pako> p60 BR Pako> set pointing azcor elcor BR Pako> onf4 ! Short Onoff integration (4 Subscans of 10 s) with central pixel 53
You may do a short onf4 after a normal pointing to monitor the pointing source flux.
Onoff and Map
Pako>onf 20 30 !Perform an on-off integration of 20 subscans of 60s with a wobbler throw of 30" BR Pako> @onf30 !Some project may have their own on-off macro
Don't try to make very long integration, you may loose the complete scan. In such a case use a loop.
Pako> bsw throw !Setup the wobbler throw BR Pako> bmap laz lel elstep azv !Setup an OTF map of laz azimuth length, lel elevation length, elstep elevation step and azv azimuth speed (arcsec/s). BR Pako> start !Start the map after you checked it is correct (it gives you the total integration time).
The speed should not be larger than ~8 arcsec/sec
NOTE: BR roff20 : set the pixel 20 for on-off (most sensitive one). BR roff53 : set the central pixel 53 (default with @wbolo) BR BR
Typical Bolo Session
A typical starting session could be as following:
Pako> @wbolo
Pako> source Mars
Pako> gain 2 ! special case for Mars, normal gain is 10
Pako> p60
Pako> bt !skydip
Pako> p60
Pako> set pointing 2. -6.
Pako> focus 1.1
Pako> start
Pako> set focus -3.5
Pako> onf4 ! Measure the flux of Mars
Pako> gain 10.
Pako> @wbolo
Pako> set project 175_05
Pako> catalog source ihet
Pako> source J0854+201 ! Pointing source
Pako> roff20
Pako> p40
Pako> set pointing 0.4 -6.4
Pako> onf4 ! Why not ?
Pako> catalog source pool
Pako> source 0927+2001 !Project source
Pako> onf 20 35 ! Do an on-off integration of 20 subscans of 60s
! with a wobbler throw of 35¨.
Pako> Ad Nauseam ... 
The set project Proj_Id will be necessary until it is automatically included in the source catalog.
List of Commands
Command |
<bgcolor='#E0E0FF'> Explanation |
|
bf |
Perform a focus |
|
Heterodyne Observation
Heterodyne observations are more complex in the sense there is much more options available. Since the NCS/Pako are still under heavy development, we give here a typical session. Some commands are the same that with bolometer observations. If the macros written by the PIs are not working ask the Pool coordinator or the AoD.
Pako> @setup-186_05-1850 ! Setup the frequencies/receivers. Tuning... Pako> source Mars Pako> pointing ! Check if continuum backends are set Pako> start Pako> set pointing -1. 2. ! The correction are given using the mira program Pako> focus 2.0 Pako> start Pako> set focus -2.2 ! The correction is given using the mira program Pako> cata source ihet Pako> source J2240+245 ! Pointing source Pako> pointing Pako> start Pako> set point -1. 0.5 Pako> catalog source pool Pako> source N821 Pako> @backends-186_05 ! maybe included in the following macro Pako> @target-wsw-186_05 Number of Loops= 5 ! according the indications of the PI. Pako> @setup-186_05-1850 ! Setup the continuum backend. Pako> source J2240+245 Pako> pointing Pako> start Pako> set point -1. 0.5 Pako> catalog source pool Pako> source N822 Pako> @backends-186_05 Pako> @target-wsw-186_05 Number of Loops= 5 Pako> Ad Nauseam ...