NIKA Data Reduction

Go back to the NIKA Main Wiki

Getting ready

To start the IDL session for the real time analysis, open a terminal and type:

   $ ssh -X nikaw-13@mrt-lx1
   $ ssh_sami
   > idl 

Shortly after a scan is done, the NIKA scientific data, the xml information generated by PAKO (and the AntennaIMBfits shortly after) are written on SAMI and can be processed. There are two types of observation: the “science” scans and the “calibration” scans. There is a specific routine to analyze each type of scan.

Calibration scans

All calibration scans are reduced by the same routine:

IDL> rta_reduce, day, scan_num

Informations or actions to be taken by the observer appear on the plots and explicitely in IDL terminal window:

cont_pointing_cross

• The plots show 1D profiles of the azimuth or elevation scans at both wavelenght for the reference detector and a gaussian fit of the source along the timeline. The displayed offsets refer to the reference detectors and are not meant to be passed to PAKO.
• The maps show the source, a cross at the location of the reference pixel and gaussian fit of the source
• In the terminal window, the observer should follow the instruction (e.g.): B 2mm (MAP) (for PAKO) SET POINTING 3.0 0.7
• the pointing reference is the 2mm channel.
• If the sky conditions were correct, instructions at 1 and 2mm should be in good agreement.
• if a glitch corrupts the maps but the 1d profiles are ok, the user can follow the instruction B 2mm, : (TOI) (for PAKO) SET POINTING 3.0 0.7
• In good conditions, all instructions agree to better than 1 arcsec.

• If the pointing is far off, the default reference pixels may not see the source and the timelines may look bad. In the terminal window, you may read the ID of the closest kids to the source and pass them to rta_reduce as keywords e.g. rta_reduce, day, scan_num, numdet1=5, numdet2=494

cont_pointing_liss

• The routine displays one map for each band, an estimation of the flux where the source is fit (red), an estimation of the flux at the center of the map (green). It also provides a quick estimate of the NEFD and the map RMS for 10arcsec equivalent pixels and the values of Tau derived by NIKA.
• The observer should follow instructions given in the terminal, e.g.: B 2mm, : (MAP) (for PAKO) SET POINTING -4.7, 1.4

cont_focus_track

• In the emacs window, edit run_focus.pro and update the day and scan num parameters.
• Check the value of focusz in the PAKO display window.
• Do not change the fooffset values unless you have modified the pako script focusp.pako.
• Save the file
• In the idl session, type .r run_focus
• Several plot windows might be on top of each other
• Follow instructions returned by the code in the terminal

cont_focus_liss

• In the emacs window, edit run focus_liss.pro and update the day and scan num parameters. Scan num should be the first of the five scans involved in this analysis.
• Save the file
• In the idl session in T2, type .r run_focus_liss
• Several plot windows might be on top of each other
• Follow instructions returned by the code in the terminal

cont_skydip

• In the emacs window, edit run_skydip.pro and update the day and scan num parameters.
• Save the file
• In the idl session, type .r run_skydip
• Several plot windows might be on top of each other
• Follow instructions returned by the code in the terminal

cont_beammap

• In the emacs window, edit run_otf_geometry.pro and update the day and scan num parameters.
• Save the file
• In the idl session in T2, type .r run_otf_geometry
• Several plot windows might be on top of each other
• Follow instructions returned by the code in the terminal

Science scans

The science scans are meant to be optimally processed offline with tailored procedures. The real time software mentioned in this note only aims at giving a quick feedback.

Total power maps

All maps (On-the-Fly and Lissajous) in Total Power Mode can be reduced by the same script:

• In the emacs window, edit run_otf_map.pro and update the scan num and day parameters.
• If you’re observing a point source, set diffuse = 0. If you’re observing diffuse emission set diffuse = 1.
• Save the file
• In the idl session, type .r run_otf_map
• Several plot windows might be on top of each other

Polarization maps

All maps (On-the-Fly and Lissajous) in Polarization Mode can be reduced by the same script:

• In the emacs window, edit run_otf_polar_maps.pro and update the scan num and day parameters.
• Save the file
• In the idl session, type .r run_otf_polar_maps
• Several plot windows might be on top of each other

Data products

Data products for the 1st NIKA pool

Neel pipeline

The following diagram shows the NIKA data flow from the IRAM 30m telescope to the observers' accounts.