Size: 2744
Comment:
|
Size: 4838
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 3: | Line 3: |
#acl CarstenKramer:read,write,delete,revert,admin All: [[Anchor(beginOfPage)]] |
#acl CarstenKramer:read,write,delete,revert,admin All:read <<Anchor(beginOfPage)>> |
Line 6: | Line 6: |
== Backends for EMIR, HERA, MAMBO == | <<TableOfContents(5)>> |
Line 8: | Line 8: |
|| || Type || Channel Width || Bandwidth || Receiver (width mode) || Remark || || '''1 MHz''' || Filterbank || 1 MHz || 4x256 MHz, 2x512 MHz, or, 1x1GHz || EMIR || (1) || || '''4 MHz''' || Filterbanks || 4 MHz || 9x1GHz || EMIR, either HERA1 or HERA2 (wide) || (2) || || '''WILMA''' || Autocorrelator || 2 MHz || 18x930 MHz || EMIR, HERA (wide) || (3) || || '''VESPA''' || Autocorrelator || 3.3 kHz-1.25 MHz || 10-512 MHz || EMIR, HERA (narrow) || (4) || || '''XPOL''' || VESPA || 40kHz-1.25MHz || 120-640MHz || EMIR || (5) || || '''ABBA''' || || || || || (6) || |
== Backends for EMIR, HERA == |
Line 16: | Line 10: |
For more information on the capabilities of EMIR, see [http://www.iram.es/IRAMES/mainWiki/EmirforAstronomers here]. In general, several backends can be attached to one receiver. Exceptions are listed below. The [http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf pako manual] describes in detail how to configure the backends. | || Backend || Type || Channel Width || Bandwidth || Receiver (width mode) || [[http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus#BackendStatus|Status]] || Remark || || '''4 MHz''' || Filterbanks || 4 MHz || 8 or 9 x 1GHz || EMIR, either HERA1 or HERA2 (wide) || {{attachment:haken.gif}} || (1) || || '''WILMA''' || Autocorrelator || 2 MHz || 16 or 18 x 930 MHz || EMIR, HERA (wide) || {{attachment:haken.gif}} || (2) || || '''FTS''' || FFTS || 195 kHz || 8x4 GHz || EMIR, HERA || {{attachment:haken.gif}} || (3.1) || || '''FTS''' || FFTS || 50 kHz || || EMIR, HERA (narrow) || {{attachment:haken.gif}} || (3.2) || || '''VESPA''' || Autocorrelator || 3.3 kHz-1.25 MHz || 10-512 MHz || EMIR, HERA (narrow) || {{attachment:haken.gif}} || (4) || || '''XPOL''' || VESPA || 40kHz-1.25MHz || 120-640MHz || EMIR || {{attachment:haken.gif}} || (5) || || '''nbc / continuum''' || continuum || 1 GHz || || || {{attachment:haken.gif}} || (6) || || '''bbc''' || continuum || 8 GHz || || || {{attachment:haken.gif}} || (7) || |
Line 18: | Line 20: |
1. '''1MHz Filterbank''': max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver. | See [[http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus|here]], for the present status of the backends. For more information on the capabilities of EMIR, see [[http://www.iram.es/IRAMES/mainWiki/EmirforAstronomers|here]]. In general, several backends can be attached to one receiver. Exceptions are listed below. The [[http://www.iram.es/IRAMES/documents/ncs30mPako/Current/PDF/pako.pdf|pako manual]] describes in detail how to configure the backends. The new backends are online! No more {{attachment:kreuz.gif}}! <CK 2-Aug-2011> |
Line 22: | Line 26: |
1. '''WILMA''': [http://www.iram.fr/IRAMFR/TA/backend/veleta/wilma/index.htm The Wideband Line Multiple Autocorrelator] for EMIR and HERA | 1. '''WILMA''': [[http://www.iram.fr/IRAMFR/TA/backend/veleta/wilma/index.htm|The Wideband Line Multiple Autocorrelator]] for EMIR and HERA |
Line 24: | Line 28: |
1. '''VESPA''': [http://www.iram.fr/IRAMFR/TA/backend/veleta/vespa/index.htm The Versatile SPectrometer Array]. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); [http://www.iram.es/IRAMES/otherDocuments/manuals/vespa_ug.ps VESPA User Guide (2002)], [http://www.iram.es/IRAMFR/ARN/dec02/node6.html Summary in IRAM Newsletter No. 54 (Dec 2002)], local contact: G. Paubert | 1. '''Fast Fourier Transform Spectrometer (FTS)''': In July 2011, the FTS and the FTS were upgraded to 32GHz bandwidth with 195 resolution for EMIR and HERA. They are available to all observers since 2-Aug-2011. See the document of Gilles Butin on the [[attachment:butin-32ghz-fts-4jul2011.pdf|Spectrum Slicers for FFT Spectrometers]] and see the [[http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus#BackendStatus|backend status page]]. In the winter semester 2010/11 we offer 8 units covering 2x4GHz of bandwidth with a fixed resolution of 195kHz for EMIR. 1. '''VESPA''': [[http://www.iram.fr/IRAMFR/TA/backend/veleta/vespa/index.htm|The Versatile SPectrometer Array]]. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); [[http://www.iram.es/IRAMES/otherDocuments/manuals/vespa_ug.ps|VESPA User Guide (2002)]], [[http://www.iram.es/IRAMFR/ARN/dec02/node6.html|Summary in IRAM Newsletter No. 54 (Dec 2002)]], local contact: G. Paubert |
Line 28: | Line 34: |
1. '''ABBA1 and ABBA2''' (Adc Bolometer Backend) are the bolometer backends, i.e. dedicated PCs connected to the bolometers. | 1. The old continuum backend, now called narrow band continuum backend '''nbc''' with 1GHz width, is still available for HERA, and also for EMIR. 1. The broad band continuum backend '''bbc''' with 8GHz width, fully exploiting the bandwidths of EMIR, is available since 2-Aug-2011. bbc cannot be connected to HERA. Decommissioned backends: 1. MAMBO2 has been decommissioned mid 2011. '''ABBA1 and ABBA2''' (Adc Bolometer Backend) were the bolometer backends for the MAMBO 1mm camera, i.e. dedicated PCs connected to the bolometers. 1. The 1MHz filterbank has been decommissioned in 4/2008: max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver. == Distribution of intermediate frequencies (IFs) to the backends (Status: July 2011) == === IF distribution installed end of June 2011 === {{attachment:fft_be2v2.JPG}} <<BR>> '''Figure 2''': Planned IF distribution for 2011 === Old IF distribution (Status: June 2011) === {{attachment:NEWBE_dec10v2.jpg}} <<BR>> '''Figure 1''': IF distribution (16-Dec-2010 SS/CK) |
Contents
Backends for EMIR, HERA
Backend |
Type |
Channel Width |
Bandwidth |
Receiver (width mode) |
Remark |
|
4 MHz |
Filterbanks |
4 MHz |
8 or 9 x 1GHz |
EMIR, either HERA1 or HERA2 (wide) |
|
(1) |
WILMA |
Autocorrelator |
2 MHz |
16 or 18 x 930 MHz |
EMIR, HERA (wide) |
|
(2) |
FTS |
FFTS |
195 kHz |
8x4 GHz |
EMIR, HERA |
|
(3.1) |
FTS |
FFTS |
50 kHz |
|
EMIR, HERA (narrow) |
|
(3.2) |
VESPA |
Autocorrelator |
3.3 kHz-1.25 MHz |
10-512 MHz |
EMIR, HERA (narrow) |
|
(4) |
XPOL |
VESPA |
40kHz-1.25MHz |
120-640MHz |
EMIR |
|
(5) |
nbc / continuum |
continuum |
1 GHz |
|
|
|
(6) |
bbc |
continuum |
8 GHz |
|
|
|
(7) |
See here, for the present status of the backends. For more information on the capabilities of EMIR, see here. In general, several backends can be attached to one receiver. Exceptions are listed below. The pako manual describes in detail how to configure the backends.
The new backends are online! No more ! <CK 2-Aug-2011>
4MHz Filterbank: max. 9 parts; use of the 4MHz filterbank excludes the use of VESPA on the same receiver. Frequency switching not available. While the channel spacing is 4MHz, the 3dB width is 5.4MHz and the noise equivalent width is 6.5 MHz
WILMA: The Wideband Line Multiple Autocorrelator for EMIR and HERA
Fast Fourier Transform Spectrometer (FTS): In July 2011, the FTS and the FTS were upgraded to 32GHz bandwidth with 195 resolution for EMIR and HERA. They are available to all observers since 2-Aug-2011. See the document of Gilles Butin on the Spectrum Slicers for FFT Spectrometers and see the backend status page. In the winter semester 2010/11 we offer 8 units covering 2x4GHz of bandwidth with a fixed resolution of 195kHz for EMIR.
VESPA: The Versatile SPectrometer Array. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); VESPA User Guide (2002), Summary in IRAM Newsletter No. 54 (Dec 2002), local contact: G. Paubert
XPOL: Line and continuum polarimetry is possible at the 30m using a new type of IF polarimeter designated XPOL. The central feature of XPOL is the correlator VESPA where the IF signals from two orthogonally polarized receivers are cross correlated to determine the four Stokes parameters. A manual is in preparation, contact: C. Thum
The old continuum backend, now called narrow band continuum backend nbc with 1GHz width, is still available for HERA, and also for EMIR.
The broad band continuum backend bbc with 8GHz width, fully exploiting the bandwidths of EMIR, is available since 2-Aug-2011. bbc cannot be connected to HERA.
Decommissioned backends:
MAMBO2 has been decommissioned mid 2011. ABBA1 and ABBA2 (Adc Bolometer Backend) were the bolometer backends for the MAMBO 1mm camera, i.e. dedicated PCs connected to the bolometers.
- The 1MHz filterbank has been decommissioned in 4/2008: max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver.
Distribution of intermediate frequencies (IFs) to the backends (Status: July 2011)
IF distribution installed end of June 2011
Figure 2: Planned IF distribution for 2011
Old IF distribution (Status: June 2011)
Figure 1: IF distribution (16-Dec-2010 SS/CK)