|
Size: 3292
Comment:
|
Size: 3635
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 8: | Line 8: |
| || || Type || Channel Width || Bandwidth || Receiver (width mode) || Remark || || '''1 MHz''' || Filterbank || 1 MHz || 4x256 MHz, 2x512 MHz, or, 1x1GHz || EMIR || (1) || || '''4 MHz''' || Filterbanks || 4 MHz || 8 or 9 x 1GHz || EMIR, either HERA1 or HERA2 (wide) || {{attachment:haken.gif}} (2) || || '''WILMA''' || Autocorrelator || 2 MHz || 16 or 18 x 930 MHz || EMIR, HERA (wide) || (3) || || '''VESPA''' || Autocorrelator || 3.3 kHz-1.25 MHz || 10-512 MHz || EMIR, HERA (narrow) || (4) || || '''XPOL''' || VESPA || 40kHz-1.25MHz || 120-640MHz || EMIR || (5) || || '''ABBA''' || || || || MAMBO || (6) || || '''Cont.''' || 1 GHz || 1 GHz || || (7) || || '''Cont.''' || 8 GHz || 8 GHz || || (8) || |
|| || Type || Channel Width || Bandwidth || Receiver (width mode) || [[http://www.iram.es/IRAMES/mainWiki/TelescopeSystemStatus#BackendStatus|Status]] || Remark || || '''4 MHz''' || Filterbanks || 4 MHz || 8 or 9 x 1GHz || EMIR, either HERA1 or HERA2 (wide) || {{attachment:haken.gif}} || (2) || || '''WILMA''' || Autocorrelator || 2 MHz || 16 or 18 x 930 MHz || EMIR, HERA (wide) || {{attachment:haken.gif}} || (3) || || '''1 MHz''' || Filterbank || 1 MHz || 4x256 MHz, 2x512 MHz, or, 1x1GHz || EMIR || {{attachment:kreuz.gif}} || (1) || || '''VESPA''' || Autocorrelator || 3.3 kHz-1.25 MHz || 10-512 MHz || EMIR, HERA (narrow) || {{attachment:haken.gif}} || (4) || || '''XPOL''' || VESPA || 40kHz-1.25MHz || 120-640MHz || EMIR || {{attachment:haken.gif}} || (5) || || '''ABBA2''' || || || || MAMBO2 || {{attachment:haken.gif}} || (6) || || '''Cont.''' || 1 GHz || 1 GHz || || || {{attachment:haken.gif}} || (7) || || '''Cont.''' || 8 GHz || 8 GHz || || || {{attachment:kreuz.gif}} || (8) || |
| Line 20: | Line 20: |
| 1. '''1MHz Filterbank''': max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver. | 1. '''1MHz Filterbank''': max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver. '''Not yet reactivated after EMIR commissioning.''' |
Backends for EMIR, HERA, MAMBO (after EMIR installation & commissioning in March/April 2009)
|
Type |
Channel Width |
Bandwidth |
Receiver (width mode) |
Remark |
|
4 MHz |
Filterbanks |
4 MHz |
8 or 9 x 1GHz |
EMIR, either HERA1 or HERA2 (wide) |
|
(2) |
WILMA |
Autocorrelator |
2 MHz |
16 or 18 x 930 MHz |
EMIR, HERA (wide) |
|
(3) |
1 MHz |
Filterbank |
1 MHz |
4x256 MHz, 2x512 MHz, or, 1x1GHz |
EMIR |
|
(1) |
VESPA |
Autocorrelator |
3.3 kHz-1.25 MHz |
10-512 MHz |
EMIR, HERA (narrow) |
|
(4) |
XPOL |
VESPA |
40kHz-1.25MHz |
120-640MHz |
EMIR |
|
(5) |
ABBA2 |
|
|
|
MAMBO2 |
|
(6) |
Cont. |
1 GHz |
1 GHz |
|
|
|
(7) |
Cont. |
8 GHz |
8 GHz |
|
|
|
(8) |
See here, for the present status of the backends. For more information on the capabilities of EMIR, see here. In general, several backends can be attached to one receiver. Exceptions are listed below. The pako manual describes in detail how to configure the backends.
1MHz Filterbank: max. 4 parts; series, parallel, or mixed mode possible; using the 1MHz filterbank with 1GHz bandwidth excludes the use of VESPA with the same receiver. The filterbank can be shifted in multiples of 32MHz from the center frequency of the connected receiver. Not yet reactivated after EMIR commissioning.
4MHz Filterbank: max. 9 parts; use of the 4MHz filterbank excludes the use of VESPA on the same receiver. Frequency switching not available. While the channel spacing is 4MHz, the 3dB width is 5.4MHz and the noise equivalent width is 6.5 MHz
WILMA: The Wideband Line Multiple Autocorrelator for EMIR and HERA
VESPA: The Versatile SPectrometer Array. Up to 18000 channels. In connection with HERA (9 pixels) the following combinations of resolution (kHz) and bandwidth (MHz) are possible: (20/40), (40,80), (80, 160), (320,320), (1250, 640); VESPA User Guide (2002), Summary in IRAM Newsletter No. 54 (Dec 2002), local contact: G. Paubert
XPOL: Line and continuum polarimetry is possible at the 30m using a new type of IF polarimeter designated XPOL. The central feature of XPOL is the correlator VESPA where the IF signals from two orthogonally polarized receivers are cross correlated to determine the four Stokes parameters. A manual is in preparation, contact: C. Thum
ABBA1 and ABBA2 (Adc Bolometer Backend) are the bolometer backends, i.e. dedicated PCs connected to the bolometers.
Continuum backend with 1GHz width, is still the old system used for the ABCD receivers
Continuum backend with 8GHz width, fully exploiting the increased bandwidth of EMIR, is in preparation.