{\rtf1\ansi\ansicpg1252\cocoartf1265\cocoasubrtf210
{\fonttbl\f0\fmodern\fcharset0 Courier;\f1\fnil\fcharset0 Menlo-Regular;}
{\colortbl;\red255\green255\blue255;}
\paperw11900\paperh16840\margl1440\margr1440\vieww23000\viewh10780\viewkind0
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\pardirnatural

\f0\fs22 \cf0 @focusOTF = 5 0.84 0 0 5 35 axel (to be able to do a focus per pixel!)\
\
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\pardirnatural
\cf0 @focusOTF Z: 20160201s 168 - 172 \'97> param.rmak_keep=30 \'97> set focus 1\
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\pardirnatural
\cf0 only with the central pixel we obtain\
\pard\tx560\tx1120\tx1680\tx2240\tx2800\tx3360\tx3920\tx4480\tx5040\tx5600\tx6160\tx6720\pardirnatural
\cf0 \CocoaLigature0 Flux A1:  0.95\
FWHM A1:  0.99\
Flux A2:  0.97\
FWHM A2:  1.40\
Flux A3:  1.17\
FWHM A3:  0.99\
\
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\pardirnatural
\cf0 \CocoaLigature1 20160201s 173 \'97> @focusliss X \'97> set focus -0.7 (param.rmax_keep=30, compatible with what we obtain with 60 or without doing any selection)\
\
20160201s 174 \'97>  @focusliss Y \'97> set focus 0.0 (param.rmax_keep=30, compatible with what we obtain with 60 or without doing any selection)\
\
\CocoaLigature0 \
\CocoaLigature1 @focusOTF Z: 20160201s \CocoaLigature0 175-179\CocoaLigature1  \'97> param.rmak_keep=30 \'97> set focus 0.9\
only with the central pixel we obtain\CocoaLigature0 \
\pard\tx560\tx1120\tx1680\tx2240\tx2800\tx3360\tx3920\tx4480\tx5040\tx5600\tx6160\tx6720\pardirnatural
\cf0 Flux A1:  0.89\
FWHM A1:  0.81\
Flux A2:  1.04\
FWHM A2:  0.86\
Flux A3:  1.02\
FWHM A3:  0.92\
\
We check the results with focusliss Z (given that it is the kind of scan that we use to optimize the focus in X and Y). With the flux at 1mm we obtain the same result we had with the focusOTF sequence (tested with \CocoaLigature1 param.rmak_keep=30 and param.rmak_keep=60\CocoaLigature0 ).\
\
@focusliss X \'97> set focus -1. /dir X\
\
@focusliss_long X \'97> set focus -1. /dir X (to verify the results of the smaller scans, we will continue with @focusliss, otherwise it takes too long and the focus will change for other reasons)\
\
@focusliss Y \'97> set focus 0.2 /dir Y\
\
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\pardirnatural
\cf0 \CocoaLigature1 @focusOTF Z: 20160201s \CocoaLigature0 185-189\CocoaLigature1  \'97> param.rmak_keep=30 \'97> set focus 0.9\
only with the central pixel we obtain\CocoaLigature0 \
\pard\tx560\tx1120\tx1680\tx2240\tx2800\tx3360\tx3920\tx4480\tx5040\tx5600\tx6160\tx6720\pardirnatural
\cf0 Flux A1:  0.93\
FWHM A1:  0.98\
Flux A2:  0.94\
FWHM A2:  0.98\
Flux A3:  1.03\
FWHM A3:  1.10\
\
@focusliss X \'97> set focus -1. /dir X \

\f1 \

\f0 @focusliss Y \'97> set focus ~0.2 /dir Y (the 4th subscan is wired), we do not change it and do a beam map\

\f1 \
\
}